Volume 44 Issue 3
May  2016
Turn off MathJax
Article Contents
Abstract
References
Related Articles
ZHOU Bo, YANG Jin, ZHOU Jianliang, LIU Zhengli, YANG Jiangang. A Jetting Flow Rate Design Method for Conductor Installation through Jetting in Deepwater Drilling[J]. Petroleum Drilling Techniques, 2016, 44(3): 21-26. DOI: 10.11911/syztjs.201603004
Citation: ZHOU Bo, YANG Jin, ZHOU Jianliang, LIU Zhengli, YANG Jiangang. A Jetting Flow Rate Design Method for Conductor Installation through Jetting in Deepwater Drilling[J]. Petroleum Drilling Techniques, 2016, 44(3): 21-26. DOI: 10.11911/syztjs.201603004
shu

A Jetting Flow Rate Design Method for Conductor Installation through Jetting in Deepwater Drilling

  • 1.

    MOE Key Laboratory of Petroleum Engineering (China University of Petroleum(Beijing)), Beijing, 102249, China;

  • 2.

    CNOOC Research Institute, Beijing, 100028, China;

  • 3.

    Shenzhen Company of CNOOC, Shenzhen, Guangdong, 518067, China

More Information
  • Received Date: July 13, 2015
  • Revised Date: February 25, 2016
    Graphical Abstract
    • Abstract
  • When conductors are installed in deepwater drilling through jetting, it is necessary to design jetting flow rate appropriately based seabed parameters so as to guarantee the proper installation of conductors and rational recovery time of conductor capacity. A computation model of minimum jetting flow rate for rock breaking was established according to the submerged water jet theory and the unconsolidated seabed failure criteria. Then a pilot simulation test was carried out on conductor (φ339.7 mm) installation by jetting to analyze the influential rules of jetting flow rate on seabed breaking and surface conductor capacity. It is shown that the lowering velocity of conductors would be slow when jetting flow rate is less than a minimum certain value. On the other hand, the lowering velocity of conductors would increase quickly with the increasing of the jetting flow rate. The conductor bearing capacity decreases exponentially with the increasing of the jetting flow rate and reaches the lowest when jetting flow rate is over 1.2 times of the minimum value. Based on the calculation model and simulation of minimum jetting flow rate, the jetting flow rate design method is established under the constraint of hydraulic seabed breaking capacity and conductor bearing capacity. It has been applied in 22 deepwater wells in the South China Sea and the installation efficiency of conductors from jetting is increased and conductor stability is guaranteed.
    • FullText(HTML)
    • References (14)
  • [1]
    汪顺文,杨进,严德,等.深水表层导管喷射钻进机理研究[J].石油天然气学报,2012,34(8):157-160. WANG Shunwen,YANG Jin,YAN De,et al.Research of jetting drilling mechanism of surface conductor in deepwater[J].Journal of Oil and Gas Technology,2012,34(8):157-160.
    [2]
    JEANJEAN P.Innovative design method for deepwater surface casings[R].SPE 77357,2002.
    [3]
    徐荣强,陈建兵,刘正礼,等.喷射导管技术在深水钻井作业中的应用[J].石油钻探技术,2007,35(3):19-22. XU Rongqiang,CHEN Jianbing,LIU Zhengli,et al.The appliation of jetting technology in deepwater drilling[J].Petroleum Drilling Techniques,2007,35(3):19-22.
    [4]
    罗俊丰,杨进,严德,等.深水钻井表层导管喷射安全等候时间窗口设计[J].石油机械,2014,42(4):53-56. LUO Junfeng,YANG Jin,YAN De,et al.Design of the safety waiting conductor jet in time window for surface subsea drilling[J].China Petroleum Machinery,2014,42(4):53-56.
    [5]
    周波,杨进,刘正礼,等.深水钻井表层导管静置时间窗口设计[J].石油勘探与开发,2014,41(2):234-238. ZHOU Bo,YANG Jin,LIU Zhengli,et al.Design of structure casing soaking time in deepwater drilling[J].Petroleum Exploration and Development,2014,41(2):234-238.
    [6]
    柯珂,张辉,周宇阳,等.深水钻井喷射下导管模拟试验装置的研制[J].石油钻探技术,2015,43(2):33-37. KE Ke,ZHANG Hui,ZHOU Yuyang,et al.The development of testing simulators for conductor jets running in deepwater drilling[J].Petroleum Drilling Techniques,2015,43(2):33-37.
    [7]
    ZHOU Bo,YANG Jin,XU Yunjin,et al.Experimental research on structural casing soaking time in deepwater drilling[R].SPE 170317,2014.
    [8]
    AKERS T J.Jetting of structural casing in deepwater environments:job design and operational practices[J].SPE Drilling Completion,2008,23(1):29-40.
    [9]
    BECK R D,JACKSON C W,HAMILTON T K.Reliable deepwater structural casing installation using controlled jetting[R].SPE 22542,1991.
    [10]
    王磊,张辉,周宇阳,等.深水钻井喷射下导管水力参数优化设计方法[J].石油钻探技术,2015,43(2):19-24. WANG Lei,ZHANG Hui,ZHOU Yuyang,et al.Optimal design of hydraulic parameters for conductor jetting in deepwater drilling[J].Petroleum Drilling Techniques,2015,43(2):19-24.
    [11]
    杜嘉鸿,张士旭.高压喷射注浆技术应用现状及新进展[J].探矿工程(岩土钻掘工程),1995,22(4):4-6,10. DU Jiahong,ZHANG Shixu.Present application and new advances of high pressure jet grouting technique[J].Exploration Engineering(Rock Soil Drilling and Tunneling),1995,22(4):4-6,10.
    [12]
    廖华林,李根生,易灿.水射流作用下岩石破碎理论研究进展[J].金属矿山,2005(7):1-5,66. LIAO Hualin,LI Gensheng,YI Can.Advance in study on theory of rock breaking under water jet impact[J].Metal Mine,2005(7):1-5,66.
    [13]
    马飞,宋志辉.水射流动力特性及破土机理[J].北京科技大学学报,2006,28(5):413-416. MA Fei,SONG Zhihui.Dynamic property and breaking soil mechanism of water jet[J].Journal of University of Science and Technology Beijing,2006,28(5):413-416.
    [14]
    周建良.深水表层导管喷射钻进过程中钻井液排量优化研究[J].中国海上油气,2012,24(4):50-52. ZHOU Jianliang.Research on the optimization of delivery capacity during jetting drilling of surface conduct in deep water[J].China Offshore Oil and Gas,2012,24(4):50-52.
    • Related Articles

  • Related Articles

    [1]XU Qicong, CHEN Dong, FENG Siheng. Development and Application of Inclination Measurement Tool While Drilling in Vertical Well Sections with High Flow Rate[J]. Petroleum Drilling Techniques, 2024, 52(2): 174-180. DOI: 10.11911/syztjs.2024041
    [2]LI Shuzhan, YANG Jin, ZHU Guojing, LI Zhong, WANG Ning. Prediction of the Minimum Depth of Setting for Conductor Anchor Node in Deep-Water Drilling[J]. Petroleum Drilling Techniques, 2023, 51(2): 29-36. DOI: 10.11911/syztjs.2022039
    [3]YANG Zhonghan, LUO Ming, CHEN Jianghua, XU Fabin, XU Jing. Cement Squeezing for Pressure-Bearing Plugging in Ultra-High Temperature and High Pressure Wells in the Yinggehai Basin[J]. Petroleum Drilling Techniques, 2020, 48(3): 47-51. DOI: 10.11911/syztjs.2020012
    [4]LIU Qingyou, QIN Song, MAO Liangjie, WANG Guorong. An Analysis of the Factors Affecting the Load-Bearing Capacity of Deep Water Drilling Conductor[J]. Petroleum Drilling Techniques, 2019, 47(5): 49-56. DOI: 10.11911/syztjs.2019099
    [5]LIU Hexing, FANG Manzong, LIU Zhiqin, XU Yilong, MENG Wenbo. Jetting-Based Conductor Running Technology Used in Ultra-Deep Water Well of Lingshui Block in the Western South China Sea[J]. Petroleum Drilling Techniques, 2017, 45(1): 10-16. DOI: 10.11911/syztjs.201701002
    [6]Ke Ke, Zhang Hui, Zhou Yuyang, Wang Lei, Feng Shilun. The Development of Testing Simulators for Conductor Jets Running in Deepwater Drilling[J]. Petroleum Drilling Techniques, 2015, 43(2): 33-37. DOI: 10.11911/syztjs.201502006
    [7]Wang Lei, Zhang Hui, Zhou Yuyang, Ke Ke, Zhang Jinshuang, Peng Xing. Optimal Design of Hydraulic Parameters for Conductor Jetting in Deepwater Drilling[J]. Petroleum Drilling Techniques, 2015, 43(2): 19-24. DOI: 10.11911/syztjs.201502004
    [8]Sun Xiaojie, Cheng Yuanfang, Li Lingdong, Cui Qing, Li Qingping. Triaxial Compression Test on Synthetic Core Sample with Simulated Hydrate-Bearing Sediments[J]. Petroleum Drilling Techniques, 2012, 40(4): 52-57. DOI: 10.3969/j.issn.1001-0890.2012.04.011
    [9]Yan Lianguo, Zhou Yucang. Horizontal Well Cementing Technology of Shale Gas Well Pengye HF-1[J]. Petroleum Drilling Techniques, 2012, 40(4): 47-51. DOI: 10.3969/j.issn.1001-0890.2012.04.010

  • Cited by

    Periodical cited type(11)

    1. 肖尧，闫振峰，李剑华. 纳米基低密高强水泥浆在赵东油田的应用. 石油地质与工程. 2023(04): 117-120+126 .
    2. 杨威，刘仕康，薛雷. 渤海浅层大位移井固井水泥浆技术. 石油化工应用. 2023(12): 37-41 .
    3. 秦江，宋凯，文华，胡顺，彭石峰. 纳米低密度水泥浆体系在页岩油水平井固井中的应用. 长江大学学报(自然科学版). 2021(02): 55-61 .
    4. 范志坤，夏忠跃，冯雷，贾佳，解健程. 雷家碛井区固井漏失层分析及固井防漏工艺技术. 复杂油气藏. 2021(03): 105-110 .
    5. 王涛，贾博超. 地层承压能力固井前动态测试方法. 探矿工程(岩土钻掘工程). 2019(02): 40-43 .
    6. 王涛. 致密气水平井固井技术——以延安气田东部上古生界气藏开发实践为例. 天然气技术与经济. 2019(01): 25-29+82 .
    7. 张建国. 一种易漏层固井低密度水泥浆研发. 当代化工. 2019(07): 1392-1395 .
    8. 王涛，吴金桥，李伟，杨先伦，王波. 高水灰比高掺量粉煤灰环保型低成本固井水泥浆的研制. 硅酸盐通报. 2019(07): 2260-2267 .
    9. 林四元，张杰，韩成，胡杰，田宗强，郑浩鹏. 东方气田浅部储层大位移水平井钻井关键技术. 石油钻探技术. 2019(05): 17-21 . 本站查看
    10. 杨先伦，王涛，徐云林，白慧芳. 一种高强低密度水泥浆体系研发及应用——以延安气田延SS井区为例. 非常规油气. 2019(06): 110-116 .
    11. 李金伟. 油田固井技术研究与应用现状及前景探讨. 当代化工研究. 2018(04): 143-144 .

    Other cited types(2)

Catalog

    Get Citation
    PDF
    XML

    Article Metrics

    Article views (2505) PDF downloads (3044) Cited by(13)
    Related

    Supervisor：SINOPEC GROUP

    Sponsor：Sinopec Research Institute of Petroleum Engineering

    Serial Number：CN 11-1763/TE, ISSN 1001-0890

    Chief Editor： WANG Minsheng

    Vice Chief Editor：LIU Xiushan, ZHOU Shiming, CHEN Zuo, YE Haichao,
    CHEN Huinian

    Address：Sinopec Science and Technology Research Center, No.197 Baisha Road, Changping District, Beijing, China

    Tel：010-56606846, 56606847, 56606848, 56606849, 56606850

    E-mail：syzt@vip.163.com

    Service Account

    Subscription Account

    Video Channel

    QR Code on Taobao

    Wechat QR Code

    Copyright © 2009《Petroleum Drilling Techniques 》 All Rights Reserved.

    京公网安备 11010502036328号 京ICP备17033152号

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return